|
|
|
SBC-i686
Board
In
EOL phase, see expected life
time. Users are advised to consider SB-iGLX as replacement.
|
|
|
Top
view
|
Bottom view
|
View
with interface cables
|
| SBC-i686
Highlights |
PC/104+ Single
Board Computer implemented by combination of the CM-i686B
module and SB-i686 baseboard
AMD
Geode CPU @
266 MHz
PCI and ISA
expansion buses in PC/104+ format
32 - 128 MB SDRAM
1 -
512 MB Flash
Disk
COM1 - 4 with RS232 / RS485 / RS422
/ TTL driver options
IrDA, LPT, GPIO,
PS/2 keyboard and mouse interfaces
3 Host USB ports
Hard and floppy
disk interfaces
Sound I/O
VGA / SXGA graphics
controller. Connectors for LCD panel and CRT monitor
Single or dual
10/100BaseT Ethernet ports (optional)
Single or Dual Card Bus
/ PCMCIA slots (optional)
Lithium battery for RTC
Small
size - 96 mm x 91 mm
|
The
SBC-i686 is a standard PC/104+ compliant, single board
computer. It is implemented by CM-i686B
module providing most of the functions, and SB-i686 carrier board
providing connectors and several additional functions. The rich
features set of the SBC-i686 is customizable according to the price /
performance targets of the user's application.
The SBC-i686 contains a PC/104+ expansion
connectors which opens it to the wide range of standard peripheral
cards. Furthermore, the SBC-i686 contains a PCMCIA / Card Bus controller and slots. A PCMCIA card may be
inserted and secured in
the slot, with no additional mechanical means. Off-the-shelf PCMCIA modules can extend the system with
capabilities such as a larger solid state disk, modem, and wireless LAN.
For more information see Developer
Resources page.
|
Block Diagram
SBC-i686
Features
"SB Option" column
specifies the P/N code of SB-i686 required to have the particular
feature. "CM Option" column
specifies the P/N code of CM-i686B required to have the particular
feature. The SBC-i686 content is the combination of features provided
by the attached CM-i686B and features implemented on SB-i686.
To have the particular feature, both CM and SB options of that
feature must be implemented.
"+" means that the feature is always available, regardless
of P/N code.
| Feature |
Specification |
SB
Option |
CM
Option |
CPU
SDRAM
Flash Disk |
See Features List of CM-i686B
module |
|
|
| COM 1 |
RS-232 levels, standard
10-pins header for DB-9 cable/connector |
+ |
+ |
| COM 3 |
Rx/Tx only, TTL
levels, 50-mil header |
+ |
+ |
| COM 2 & 4 |
RS-232 / RS-485 / RS-422 / TTL level
options, 50-mil header |
X,Y |
S |
| IrDA / COM5 |
Standard header for SIR LED module or
COM 5 Tx/Rx TTL |
+ |
+ |
| LPT (Parallel Port) |
Standard
26-pin header for DB-25 cable/connector. Shared with FDC |
+ |
S |
| IDE |
PIO and ATA-33 modes. Standard
40-pin header for HDD cable. |
H |
+ |
| FDC |
Routed through LPT header |
+ |
S |
| Ethernet |
One or two 10/100BaseT Ethernet
ports. Realtek RTL8139 controller with MAC and PHY functions, PCI
interface.
10-pins header per port. Optional interface module with
transformer, RJ-45 connector and activity LEDs. |
+
or
E2 |
E |
| CRT Monitor |
10-pins header. Optional
interface module with standard HD-15 VGA connector. |
+ |
Gx |
| TFT Panel |
51-pos FPC connector for
direct interface to certain TFT panels |
L |
Gx |
| STN Panel |
24-pos FPC connector for
direct interface to certain STN panels with built-in controller. (STN
panels w/o built-in controller are not supported) |
+ |
+ |
| PS/2 |
Standard headers for PS/2
cable/connector |
+ |
S |
| GPIO |
20 lines, through 50-mil header. |
+ |
S |
| ADC |
Analog to Digital converters, 8-bit, 6
channels. Through 50-mil header. |
+ |
S |
| PCMCIA / Card Bus |
TI PCI1420 controller. Support for
16-bit PCMCIA and 32-bit CardBus standards.
Single or dual PCMCIA / Card Bus slot
with card guides, for cards type I, II and III. |
Cx |
+ |
| USB |
3 Host ports, 12 Mbps. Header for
Type-A cable/ connector. |
U |
+ |
| Sound I/O |
Header for standard
cable/connectors for Microphone
(mono), Line input and Speakers (stereo) |
+ |
A |
| PC104 |
ISA bus through
standard PC/104 connector |
P |
+ |
| PC104+ |
PCI bus through
standard PC/104+ connector |
R |
+ |
Electrical,
Mechanical and Environmental Specifications
| Power Supply |
5.0V or 3.3V
(The 3.3V option is only for cards without Audio and Super-I/O chips) |
| Dimensions |
96 mm x 91 mm
x [10-22 ] mm.
Height ranges from 10 mm to 22 mm, depending on the
connectors assembled. Height specified includes the CM-i686B module. |
| Operation temp (case) |
| Commercial: |
0o to 70o C |
| Extended: |
-20o to 70o
C |
| Industrial: |
-40o to 85o C. Click for availability
note |
|
| Weight |
135 gram |
| Storage
temperature |
-40o to 85o
C |
| Relative
humidity |
10% to 90% (operation)
05% to 95% (storage) |
| Shock |
50G / 20 ms |
| Vibration |
20G / 0 - 600 Hz |
| MTBF |
> 100,000 hours |
For more information see:
- SB-i686
Reference Guide
- Developer Resources
|
